A guide to setting up the Linksys/Sipura SPA and SPA as an FXO Gateway simplified installation and configuration instruction by JMG Technology. Sipura SPA Simplified Users Guide Version b A Step by Step Introduction Written by Jason from JMG Technology Section 1 Getting Started When you. PSTN-VoIP gateway. SPA information Software And this http://www. Or, go to this line.
|Published (Last):||12 July 2008|
|PDF File Size:||3.61 Mb|
|ePub File Size:||13.28 Mb|
|Price:||Free* [*Free Regsitration Required]|
If you enter a followed by 6 more digits you call will not be placed. This is the same as the subnet mask managed by your router. After you hear “Option Successful,” hang-up.
That’s the entire configuration that the Quadro needs. SPA will prompt for confirmation. Finally Enable the Service and press the Save Button. Now you can drag the configuration file back onto your device whenever you want to reset the device configuration. Dial Write down the IP address that is returned Step 7: How much did that misrouted call cost you again?
However they are invaluable feature of the SPA so you should at least learn the basics of how they work. You will notice that a separates the 1st dial plan from the 2nd.
Here is the link to the SPA configuration pages. Click on the settings tab. Unit will reboot and all configuration parameters will be reset to factory default values. The steps described below uses the second method mainly because it does not use any IP lines. What this means is any number you dial after typing 1 will go out through gateway 1.
The author adds the newest version at the bottom of the list, so take the last version available. The file you have saved can be used to restore your configuration later if something goes wrong or can be sent to another user to assist in trouble shooting.
You will need to connect your computer. To stop this happening, you need to make the ear piece quieter, and also make the mouth piece less sensitive. In the section Internet Connection Typeyou need to make the following changes:. I am using 3. You will probably notice tecbnology that there is no zpa3000 echo.
You will also need the following: These issues really are “features” vs “bugs” of the SPA, because the Sipura designers deliberately designed the adapter to behave this way. The setup guide provided here was orginally authored by Jason.
This might include network and service provider data.
Using a SPA-3000 as FXO Gateway to a Quadro 2x
Analog Telephone Adapter Network settings via Keypad commands: It should reboot your SPA. This error is caused if More information. Alternatively you could try a bricks and mortar retailer like Harris Technology but you should check they have them in stock before going shopping.
Enter IP address using numbers on the telephone key pad. Generally speaking, increasing these settings increases echo and volume, and decreasing the settings decreases echo and volume. So if you rang the actual number that would be called would be Dial Plan 5: In that case, all you do is add in some dial-plan tehnology that allow you to dial via alternate accounts often setup on the the SPA’s “gateway” fields.
Using a SPA as an FXO Gateway to a Quadro 2x – The VoIP
This allows the SIP Module to be configured from any computer or. Configure your settings. After confirming, you will hear “Option Successful.
Now the block seems to work, so I don’t know under what conditions it would be bypassed, but the telco did warn me that they didn’t “guarantee” my toll call block Echo can be created by your telephone techbology or one of the gain settings ttechnology your SPA Make sure the phone is connected securely to your router or. It also has an auto-configuration option when used with a Quadro PBX.
Sipura SPA-3000 Simplified Users Guide Version 1.1b
Going forward, you can simply add a 3rd Party Softphone and use those credentials to More information. Initial setup If your Soundstation does not automatically register More information. When you dial Emergency number your call will go out through Gateway 0 which is your normal PSTN line, immediately S0 after you have dialed the 3rd tschnology.
It is OK to upgrade to the latest 3. Proxy and Registration Settings Proxy: What you use will depend on your router. The second method is just to use SIP and create the appropriate Call routing entries.
You will need to suspend your PC rather than switch it off for this to work. You will need to enter this setting as the static subnet mask shortly. ASAIK this can’t be done However, if all you want is a manual i.